switch with iec connector compact size two function power entry module combining a dpst switch and an iec 320 power line connector. compact packaging allows a smaller panel cutout with choice of snap-in or flange mounting. available with general purpose filtering (f models - cfs, cfe), medical application filtering (h models- chs, che) or unfiltered (cs, ce). terminals allow for easy connection to any wiring scheme. preconnected terminals from line to switch are available (b models - cbs, cbe) for reducing oem wiring time. the medical versions (h models) are designed specifically for health care applications. their extremely low leakage current allows compliance with ul544 and ul2601 as well as csa22.2 health care specifications for use with both patient and non-patient care equipment. for more information on ul544 or ul2601, see appendix c. note: when using the models with an iec connector, remember that the leakage current of the companion line cord, ga400, is more significant than that of the filter - which may disqualify this line cord from use in patient care applications. specifications maximum leakage current, each line to ground: ? f models h models @120 vac 60 hz: .25 ma 2 a @250 vac 50 hz: .40 ma 5 ? hipot rating (one minute): line-to-ground 2250 vdc line-to-line 1450 vdc operating frequency: 50/60 hz rated voltage: 250 vac operating voltages: 115/230 vac switch: double-insulated rated for 10,000 operations at full load. 51 amp inrush capability. unfiltered push-on force: 18 lb/80 n minimum insertion loss in db: line-to-ground in 50 ohm circuit current frequency mhz rating 0.05 0.15 0.5 1 5 10 30 f models 0 1a 10 26 46 48 46 47 46 0 3a 8 16 32 36 43 48 50 0 6a 4 11 22 27 36 41 50 10a 1 4 14 18 27 33 42 h models 0 1a 16 21 37 44 26 21 10 0 3a 9 14 31 32 26 24 14 0 6a 4 10 22 23 19 18 13 10a 2 6 10 15 11 11 9 line-to-line in 50 ohm circuit current frequency mhz rating 0.05 0.15 0.5 1 5 10 30 f models 0 1a 1 3 13 28 62 67 42 0 3a 2 6 14 23 65 65 67 0 6a 2 6 14 27 46 48 58 10a 1 7 14 23 42 44 62 h models 0 1a 1 6 13 29 38 42 26 0 3a 1 5 10 22 36 34 36 0 6a 1 5 14 20 31 33 37 10a 1 4 11 19 32 37 38 110 catalog 1654001 dimensions are in inches and dimensions are shown for usa cust. svc.: 1-800-468-2023 www.corcom.com revised 05-07 millimeters unless otherwise reference purposes only. corcom prods: 1-847-680-7400 www.tycoelectronics.com specified. values in italics specifications subject germany: 49-89-6089-0 are metric equivalents. to change. c series c series corcom product guide ul recognized csa certified vde approved c fs cs electrical schematics resistor location for reference only. f models (cfs, cfe) h models (chs, che) b models (cbs, cbe) ? applies to filtered models only. line load line load n power on/off l g l g n note 1: jumpers provided on cbs and cbe versions onl y. note 2: location of optional filter note 1 note 1 note 2 note 2
case dimensions abc def .006 .006 .006 part no. (max) (max) (max) .152 .152 .152 cs, cbs 1.23 .97 1.62 1.06 1.54 31.24 24.64 41.17 26.92 39.12 ce, cbe 1.74 .97 1.62 1.06 1.54 1.417 44.2 24.64 41.17 26.92 39.12 36.0 cfs, chs 1.23 2.53 1.62 1.12 1.54 31.24 64.26 41.17 28.5 39.12 cfe, che 1.74 2.53 1.62 1.12 1.54 1.417 44.2 64.26 41.17 28.5 39.12 36.0 switch with iec connector compact size (continued) 111 catalog 1654001 dimensions are in inches and dimensions are shown for usa cust. svc.: 1-800-468-2023 www.corcom.com revised 05-07 millimeters unless otherwise reference purposes only. corcom prods: 1-847-680-7400 www.tycoelectronics.com specified. values in italics specifications subject germany: 49-89-6089-0 are metric equivalents. to change. p o w e r e n t r y m o d u l e s c series corcom product guide cs, cbs * cfs, chs ce, cbe * cfe, che cbs, cbe pre-connected terminals part numbers 0 1cfs1 0 1cfe1 0 1chs1 0 1che1 0 3cfs1 0 3cfe1 0 3chs1 0 3che1 0 6cfs1 0 6cfe1 0 6chs1 0 6che1 10cfs1 10cfe1 10chs1 10che1 10CS1 10ce1 10cbs1 10cbe1 recommended panel cutout panel cutout for thickness of .031- .098 [ .8-2.5 ]. not recommended for plastic panels. for snap-in applica- tions, the d sides of the cutout must have a .02 [. 508 ] radius on the instal- lation side. snap-in models allow front mounting only. typical dimensions: mounting holes: .13 [ 3.3 ] dia. (2) with .23 dia. x 90? counter sunk terminals: .250 [ 6.35 ] (3) holes: .07 [ 1.8 ] dia. case styles a c b .21 1 5.36 max. c b .21 1 5.36 max. a a c b .2 1 1 5 .36 m ax. f a c b .2 1 1 5 .36 max. f 1.04 26.4 max cbs rear view cbe rear view cbs, cbe side view e f d r max .06 1.52
|
